Skykit Control lets you make changes to devices in two ways:
Send a command to make a device do something once.
Set a configuration to change how a device behaves from now on.
Knowing which is which tells you whether a change will reach a device that's offline. This page explains the difference and lists the commands and configurations you can use in Skykit Control.
What's the difference?
Command | Configuration | |
|---|---|---|
What it is | A one-time instruction the device carries out right away | A saved setting the device keeps and applies |
Examples | Reboot, screenshots, app updates | Timezone, rotation, volume, scheduled reboot |
Device must be online? | Yes | No |
Where to see results | Event History and, for bulk commands, Job Status | Status Tab (Reported vs. Configure columns) and the Device Config Report |
Where you send it | Device detail page, or Bulk Action > Send Command | Status Tab (Save Configuration), or Bulk Action > Settings and Configurations |
A simple way to tell them apart: a command is something the device does; a configuration is something the device is. For example, Reboot Device is a command, but Scheduled Reboot is a configuration, because the device keeps rebooting on that schedule until you change it.
What happens when a device is offline?
Commands are not queued. If a device is offline when you send a command, it never receives it, and it won't run the command when it comes back online. Bulk commands sent to offline devices show an error in Job Status. Send the command again once the device is back online.
Configurations wait for the device. You can save a configuration for an online or offline device. An offline device picks up the change the next time it checks in. Until then, the Reported and Configure values will not match in Skykit Control.
Reported values are what the device last reported back to Skykit as its configuration.
Configure values are what is set for the device in Skykit Control. Offline devices check for and apply configuration changes when they come back online.
Note
It can take some time for a new configuration to apply, even on an online device. If the Reported and Configure values still don’t match after several hours, contact Skykit Support at support@skykit.com and include the device serial number, the setting you changed, and the current behavior of the device.
One exception to keep in mind: a scheduled firmware update is set up ahead of time but behaves like a command. The device must be online at the scheduled time or the update won't run.
Commands and Configurations in Skykit Control
The tables below list what you can send or set in Control. The Bulk Action column shows whether you can apply it to many devices at once from the Devices list.
Commands (device must be online)
Using Bulk Actions?
Skykit Control will allow you to send commands to any device via Bulk Actions, but those commands will not be received by offline devices. When attempting to send commands to individual devices, buttons to send commands will be inactive on offline devices.
Command | Where to find it | Bulk Action | What it does |
|---|---|---|---|
Reboot | Status Tab | Yes | Restarts the device. |
Factory Reset | Status Tab | No | Erases all data, including saved Wi-Fi, and restores factory settings. Can't be undone. |
Reset Password | Status Tab | No | Changes the device password (exit code) used to leave kiosk mode. |
Modem Reset | Network Tab (cellular devices only) | No | Resets the cellular modem remotely. |
Download and install firmware OTA (over the air) | Firmware Tab | Yes | Downloads and/or installs firmware updates. Bulk commands can only send these commands immediately. The firmware Tab supports scheduled updates. |
Update Apps | Apps Tab | Yes (Update All, Home, Control, or Player) | Updates apps to the latest available version. |
Launch/Start or Reset Apps | Apps Tab | Yes (for Home, Control, or Player apps) | Launches or resets the app specified. Apps other than Home, Control, and Player do not have Bulk Actions support. |
Uninstall Apps | Apps Tab | No | Uninstalls the app. Uninstalling a managed app results in it being reset to the factory version. |
Display on / off (HDMI-CEC) | Peripherals Tab (Test Standby/Sleep, Test Wake/Power On) | Yes | Turns the connected display off or on. CEC must be enabled on the display. |
Take Screenshot | Live Monitoring Tab | Yes | Captures an image of what's playing on the display. |
Start Live View | Live Monitoring Tab | No | Streams the display in real time. |
Configurations (saved; offline devices update when they reconnect)
Configuration | Where to find it | Bulk Action | What it controls |
|---|---|---|---|
Volume | Status Tab | Yes | Display volume. |
Brightness | Status Tab | Yes | Screen brightness. |
Timezone | Status Tab | Yes | Device timezone; also used for scheduled reboots and firmware updates. |
Rotation | Status Tab | Yes | Screen orientation. |
Ignore Accelerometer | Status Tab | Yes | Whether the screen rotates automatically with the display (if supported by hardware). |
Scheduled Reboot (Reboot Day, Reboot Time) | Status Tab | Yes | Reboots the device at a set day and time whether or not the device is online. |
Kiosk Application | Status Tab | Yes | The app that launches after the home screen; Skykit Player by default. |
Home/Launcher Application | Status Tab | Yes | The home app package; Skykit Home by default. |
Kiosk Lock Mode | Status Tab | Yes | Locks onscreen navigation controls such as Back. |
Hide Navigation Bar | Status Tab | Yes | Shows or hides the Android navigation bar. |
Auto Launch Home | Status Tab | Yes | Launches Skykit Home on boot. |
Device Density | Status Tab | Yes | Pixel density for Web Views, Dashboards, and Code Bundles. |
Display Width / Display Height | Status Tab | No | Overrides screen size in pixels. Rarely needed. |
Unified View | Status Tab | Yes | Extends content across two displays (supported displays only). |
Android Debug Bridge (ADB) | Status Tab | Yes | Enables or disables ADB for developer use. |
Unified Layout | Status Tab (E500 only) | No | Arranges multiple screens on one E500. |
Device Frame Buffer | Status Tab (E100 only) | Yes | Screen resolution with multiple screens. |
Disallow USB Usage | Status Tab | Yes | Blocks most USB devices; mice and keyboards still work. |
Network Time Server | Status Tab | No | Alternate time server. Most devices shouldn't change this. |
App Receiver Key | Status Tab | No | Lets third-party apps send commands to Skykit apps. |
Managing Wi-Fi networks | Network Tab | No | Adds or removes Wi-Fi network credentials. |
Wi-Fi, Bluetooth, or Location Enabled | Network Tab | Yes | Turns Wi-Fi, Bluetooth, or Location Services capabilities on and off. |
Enable CEC | Peripherals Tab | Yes | Allows the player to receive off and on commands via HDMI-CEC. |
Set CEC command type | Peripherals Tab | No | Sets which type of commands the player receives from HDMI-CEC. |